Forums › General Discussion › PVC plumbing and cockpit drains › Re: PVC plumbing and cockpit drains

#69215
unabated
Participant

I drain the hot water tank, after relieving any
pressure in the system. I disconnect the in and out
hoses to the tank and install a setup I made with
unions to the reconnect the pressure system without
the hot water heater connected. Which BTW is a great
to have in case your heater craps out while your away
from the dock, you can always install this thing and
be able to use the preussre system.

I then drain each of the tanks till almost dry, I then
remove the hose at the source side of the galley pump
and attach a dry vac to it,sucking out any remaining
fluid.
This way the system is dry, no pink fluid is left and
if there is any liquid left, it wont freeze.
Although I hear some people use vodka cause it’s
cheaper than the pink stuff.

— Robert Fine <> wrote:

Ah Rich,

I have a better way to winterize. And it doesn’t
involve that awful tasting
anti-freeze that only gets rinsed out at the end of
the season.

I install a shore water inlet. At a dock, I use a
hose and hey! presto
fresh water without using the tank and pump.

But when winterization comes along, baby, that’s
where it shines! I connect
a fitting made up to match an air compressor with
the hose fitting. One by
one, from the farthest to the nearest I open up the
faucet, cold first, hot
last, and run it until no more water blows out.

The hot water heater is drained, the cold water is
dry (as is the hot
water), and if there are a few drops of water in the
system, so what? As
long as there’s expansion space it’s all good.

I also drain the tanks to the bilge using a siphon
on a fitting before the
pressure pump.

This all takes about an hour. The nice thing is
that there’s no
polyproplyene glycol in the system (ever had a
colonoscopy? The stuff they
make you drink a gallon of? That pink stuff without
the pink. You still
want it in your water system?)

Bob

On Tue, Mar 11, 2008 at 3:54 PM,
<> wrote:

Bob
I would have mixed feelings about using PVC or

copper for pressure water

lines in the boat. I’ve experienced problems with

the end fittings used

with plastic tubing. Most of these problems have

been addressed by

replacing the cheap plastic fittings with copper

compression fittings and

nylon compression rings. I don’t believe the

nylon rings are available

anymore, but copper compression rings are. Too

bad, since the nylon

compression rings allowed you to disassemble the

fitting and reuse the

parts. I’ve not had very good results reusing

fittings with copper

compression rings.

I’ve still had issues with the hot water line from

the water heater.

Water in the water tank gets hotter than what you

would normally find in a

domestic water system. I’ve had issues with the

water line breaking. I

lost count of how many times I dumped a water tank

into the bilge last year.

I eventually replaced the hose from the water

heater to the manifold with

nylon reinforced tubing.

Friends of mine built a cabin in the woods in

central New Hampshire a few

years ago. When the plumbed the camp, they

pitched the water lines and

installed drains at the low points so as to make

winterizing easy for them.

I suppose you could do this with the pressure

water system on your boat,

but snaking water pipe through cabinets and bilge

doesn’t lend itself to

pitching the pipes as you might wish. We have a

camp in NY, but our pipes

weren’t put in this way. Its a pain to blow them

out when winterizing.

Sometimes we don’t get all the water out of one

spot or anther and the pipe

splits open when the water freezes. I think you

would find it difficult to

reliably blow the pipes out.

On the other hand, winterizing is pretty easy with

the plastic tubing.

All I have to do is drain the water heater, open

the faucets, remove the

water filter and toss a gallon of potable

anti-freeze in the water tanks.

If it were hard plastic or copper, I’d have to

blow out the lines. This

would be problematic.

Folks who keep their boats in slips might have a

direct connection to a

water supply. If I used this kind of connection,

I’d want a fresh water

system that was pretty reliable. I’d hate to come

back to the boat to find

that one of the water lines had broken and allowed

the bilge to flood with

city water. One would think that a shutoff of

some kind would prevent this

kind of problem, but I know I’d eventually forget

to turn the water off. I

think the right solution is to use a better

quality plastic tubing than

Pearson used. Someone must make something like

this. West Marine sells

something with the Whale brand on it, but it’s

very expensive. If anyone

has a suggested supplier for quality tubing at a

reasonable price, please

let us know.

—
Rich Carter
—
Rich Carter


Original message


From: “Robert Fine” <>

I wonder, what do you all think of re-doing the

potable water with

copper

piping like a house? Assuming of course, fixed

connections to tanks

were

via small sections of hose?

Bob

On Tue, Mar 11, 2008 at 9:48 AM, alan P

<> wrote:

A few yrs ago had a Catalina 30 in the yard

that had a

small leak in his winter cover. Water had

leaked in

and when it froze, busted a scupper hose. In

the

spring when it rained, more water had leaked

into the

boat.
The travel lift operator needed to move the

boat to

launch someone else. When he lifted the boat

up, all

the water shifted, causing the boat to tip in

the

slings. The Catalina ended bow up, sitting on

the

rudder. Not a pretty site.
a
— Silver Heels <> wrote:

I did not mean to say unexpected stuff can’t

happen,

like something clogging up Rich’s cockpit

drain

pipe. Remind me to
tell you some time about wintering my last

boat in

Greece, where a cat got in through a

sheltered

cockpit porthole I’d
left open for ventilation and had a litter

of

kittens on my bunk. And that was only the

beginning

of the mess!

Tor


Silver Heels, P-424 #17
http://www.SilverHeels.us



Original Message


From: alan P [mailto:]
Sent: Tuesday, March 11, 2008 7:03 AM
To: Mailing List
Subject: RE: PVC plumbing and

cockpit

=== message truncated ===

____________________________________________________________________________________
Never miss a thing. Make Yahoo your home page.
http://www.yahoo.com/r/hs

Post generated from Pearson424 Forum using Mail2Forum