- This topic has 28 replies, 7 voices, and was last updated 18 years, 4 months ago by
.
-
Posts
-
-
I have searched the globe for Westerbeke 60 fuel lines with no luck. They are most certainly no longer available from the manufacturer. Does anyone have any ideas on sources for custom fuel line manufacturing resources?
Any thoughts are welcome.
Thanks!
-Bill Emberley
Running Tab #86Post generated from Pearson424 Forum using Mail2Forum
-
Hi Bill,
Do you need a full set? Or do you need one or the other repaired? I wonder if the part from a W58 would work as they're very nearly identical?
Bob
On Mon, Jun 16, 2008 at 12:36 PM, Bill Emberley < ([email][/email])> wrote:
I have searched the globe for Westerbeke 60 fuel lines with no luck. They are most certainly no longer available from the manufacturer. Does anyone have any ideas on sources for custom fuel line manufacturing resources?
Any thoughts are welcome.
Thanks!
-Bill Emberley
Running Tab #86—
Bob Fine
Fine Software LLC
Your data on the web your way. No kiddingPost generated from Pearson424 Forum using Mail2Forum
-
I had very good experience dealing with mesa hose making new hoses for the transmission oil lines. They were fast and pretty reasonably priced.
They also made me a very stainless steel braided line for the trans to shaft brake.
http://www.socalsail.com/bg/co/mesa-hose-and-supply/
I dunno if they have a better website than that.
I wouldn’t recommend ‘hose man’ who are much larger. They stunk 🙂
On 6/16/08 12:46 PM, Robert Fine wrote :
Hi Bill,
Do you need a full set? Or do you need one or the other repaired? I wonder if the part from a W58 would work as they’re very nearly identical?
Bob
On Mon, Jun 16, 2008 at 12:36 PM, Bill Emberley <> wrote:
I have searched the globe for Westerbeke 60 fuel lines with no luck. They are most certainly no longer available from the manufacturer. Does anyone have any ideas on sources for custom fuel line manufacturing resources?
Any thoughts are welcome.
Thanks!
-Bill Emberley
Running Tab #86Post generated from Pearson424 Forum using Mail2Forum
-
Hi Bill,
You're looking for the injector tubing, right? Not just any fuel line?
Bob
On Mon, Jun 16, 2008 at 12:51 PM, Aaron Lynch < ([email][/email])> wrote:
I had very good experience dealing with mesa hose making new hoses for the transmission oil lines. They were fast and pretty reasonably priced.
They also made me a very stainless steel braided line for the trans to shaft brake.
http://www.socalsail.com/bg/co/mesa-hose-and-supply/
I dunno if they have a better website than that.
I wouldn’t recommend ‘hose man’ who are much larger. They stunk 🙂
On 6/16/08 12:46 PM, Robert Fine wrote :
Hi Bill,
Do you need a full set? Or do you need one or the other repaired? I wonder if the part from a W58 would work as they're very nearly identical?
Bob
On Mon, Jun 16, 2008 at 12:36 PM, Bill Emberley < ([email][/email])> wrote:
I have searched the globe for Westerbeke 60 fuel lines with no luck. They are most certainly no longer available from the manufacturer. Does anyone have any ideas on sources for custom fuel line manufacturing resources?
Any thoughts are welcome.
Thanks!
-Bill Emberley
Running Tab #86—
Bob Fine
Fine Software LLC
Your data on the web your way. No kiddingPost generated from Pearson424 Forum using Mail2Forum
-
Hi Bob,
I would like to replace all with new.
BillRobert Fine <> wrote:
Hi Bill,
Do you need a full set? Or do you need one or the other repaired? I wonder if the part from a W58 would work as they’re very nearly identical?
Bob
On Mon, Jun 16, 2008 at 12:36 PM, Bill Emberley < ([email][/email])> wrote:
I have searched the globe for Westerbeke 60 fuel lines with no luck. They are most certainly no longer available from the manufacturer. Does anyone have any ideas on sources for custom fuel line manufacturing resources?
Any thoughts are welcome.
Thanks!
-Bill Emberley
Running Tab #86—
Bob Fine
Fine Software LLC
Your data on the web your way. No kiddingEdit One Productions, Inc.
2310 Clement Avenue
Alameda, CA 94501Studio 510-814-9519
Fax 510-814-6945
Cell 415-279-1340Post generated from Pearson424 Forum using Mail2Forum
-
Thanks Aaron,
I’ll give these guys a try and report back.
-BillAaron Lynch <> wrote:
Re: Fuel Line Fabricators? I had very good experience dealing with mesa hose making new hoses for the transmission oil lines. They were fast and pretty reasonably priced.
They also made me a very stainless steel braided line for the trans to shaft brake.
http://www.socalsail.com/bg/co/mesa-hose-and-supply/
I dunno if they have a better website than that.
I wouldn’t recommend ‘hose man’ who are much larger. They stunk 🙂
On 6/16/08 12:46 PM, Robert Fine wrote :
Hi Bill,
Do you need a full set? Or do you need one or the other repaired? I wonder if the part from a W58 would work as they’re very nearly identical?
Bob
On Mon, Jun 16, 2008 at 12:36 PM, Bill Emberley <> wrote:
I have searched the globe for Westerbeke 60 fuel lines with no luck. They are most certainly no longer available from the manufacturer. Does anyone have any ideas on sources for custom fuel line manufacturing resources?
Any thoughts are welcome.
Thanks!
-Bill Emberley
Running Tab #86Edit One Productions, Inc.
2310 Clement Avenue
Alameda, CA 94501Studio 510-814-9519
Fax 510-814-6945
Cell 415-279-1340Post generated from Pearson424 Forum using Mail2Forum
-
Yes, it is aluminum tubing. In a perfect world, I would like to replace all 4 injector lines and the 2 pump to primary filter lines. I would keep the used ones for spares.
-BillRobert Fine <> wrote:
Hi Bill,
You’re looking for the injector tubing, right? Not just any fuel line?
Bob
On Mon, Jun 16, 2008 at 12:51 PM, Aaron Lynch < ([email][/email])> wrote:
I had very good experience dealing with mesa hose making new hoses for the transmission oil lines. They were fast and pretty reasonably priced.
They also made me a very stainless steel braided line for the trans to shaft brake.
http://www.socalsail.com/bg/co/mesa-hose-and-supply/
I dunno if they have a better website than that.
I wouldn’t recommend ‘hose man’ who are much larger. They stunk 🙂
On 6/16/08 12:46 PM, Robert Fine wrote :
Hi Bill,
Do you need a full set? Or do you need one or the other repaired? I wonder if the part from a W58 would work as they’re very nearly identical?
Bob
On Mon, Jun 16, 2008 at 12:36 PM, Bill Emberley < ([email][/email])> wrote:
I have searched the globe for Westerbeke 60 fuel lines with no luck. They are most certainly no longer available from the manufacturer. Does anyone have any ideas on sources for custom fuel line manufacturing resources?
Any thoughts are welcome.
Thanks!
-Bill Emberley
Running Tab #86—
Bob Fine
Fine Software LLC
Your data on the web your way. No kiddingEdit One Productions, Inc.
2310 Clement Avenue
Alameda, CA 94501Studio 510-814-9519
Fax 510-814-6945
Cell 415-279-1340Post generated from Pearson424 Forum using Mail2Forum
-
Why not just stop in a garage that deals with tractor
or truck engines. I am sure you can make these lines
up without resorting to custom lines. or am I
oversimplfing this.
alan— Bill Emberley <> wrote:
Hi Bob,
I would like to replace all with new.
BillRobert Fine <> wrote: Hi Bill,
Do you need a full set? Or do you need one or the
other repaired? I wonder if the part from a W58
would work as they’re very nearly identical?Bob
On Mon, Jun 16, 2008 at 12:36 PM, Bill Emberley
<> wrote:
I have searched the globe for Westerbeke 60 fuel
lines with no luck. They are most certainly no
longer available from the manufacturer. Does anyone
have any ideas on sources for custom fuel line
manufacturing resources?
Any thoughts are welcome.
Thanks!
-Bill Emberley
Running Tab #86—
Bob Fine
Fine Software LLC
Your data on the web your way. No kiddingEdit One Productions, Inc.
2310 Clement Avenue
Alameda, CA 94501Studio 510-814-9519
Fax 510-814-6945
Cell 415-279-1340
To unsubscribe, e-mail:
For additional commands, e-mail:Post generated from Pearson424 Forum using Mail2Forum
-
I googled “tubing fabricators” and finally cracked the code.
Check this out… http://www.iqsdirectory.com/tube-fabricating/
There are several to choose from who fabicate all types of tubing for all applications. I am off to the boat to photograph and remove fuel lines to send off. I will report back on the best resource after I make some calls.
Maybe I’ll get fancy and use stainless instead of aluminum.
-Billalan P <> wrote:
Why not just stop in a garage that deals with tractor
or truck engines. I am sure you can make these lines
up without resorting to custom lines. or am I
oversimplfing this.
alan— Bill Emberley wrote:
Hi Bob,
I would like to replace all with new.
BillRobert Fine wrote: Hi Bill,
Do you need a full set? Or do you need one or the
other repaired? I wonder if the part from a W58
would work as they’re very nearly identical?Bob
On Mon, Jun 16, 2008 at 12:36 PM, Bill Emberley
wrote:
I have searched the globe for Westerbeke 60 fuel
lines with no luck. They are most certainly no
longer available from the manufacturer. Does anyone
have any ideas on sources for custom fuel line
manufacturing resources?
Any thoughts are welcome.
Thanks!
-Bill Emberley
Running Tab #86—
Bob Fine
Fine Software LLC
Your data on the web your way. No kiddingEdit One Productions, Inc.
2310 Clement Avenue
Alameda, CA 94501Studio 510-814-9519
Fax 510-814-6945
Cell 415-279-1340
To unsubscribe, e-mail:
For additional commands, e-mail:Edit One Productions, Inc.
2310 Clement Avenue
Alameda, CA 94501Studio 510-814-9519
Fax 510-814-6945
Cell 415-279-1340Post generated from Pearson424 Forum using Mail2Forum
-
I was once told that I needed a matched set of fuel lines by three different boat mechanics. They were available at that time from Norshipco in Norfolk, VA. To the tune of $565 that of course included shipping. I could not believe that the lines had to be so precise. I got in my car and started driving after four stops, three cities and about 200 miles I walked into Southeastern Diesel on the side of the highway. Outside there were logging machines and old oily trucks. When I walked through the door I saw fuel lines hanging from the white walls. There were several engines from a 65 Hatteras and glass cases full of injector pumps. The man in the white lab coat said ” that fuel line looks like it came of a Perkins”. I had cracked the retainer nut on the end of the line and it leaked. I told the man in the lab coat that the boat mechanics told me the lines had to be the exact same and I needed a new one. He called to an older man in back that came out in his white lab coat and took my line in back. In less than a minute he returned with a new compression fitting on the line and told me that he had trimmed about 1/4″ off. I told the old man what the others had told me and he said that if it didn’t work that he would give my $2.50 back for the repair.
The moral to this story is look for a heavy equipment or other than marine source and the price will be significantly cheaper. By the way that $2.50 repair worked just fine for about ten years.Linus
<.. snip>
Post generated from Pearson424 Forum using Mail2Forum
-
Bill, call me I have two used sets. 804-370-2271.
On 6/16/08, Bill Emberley < ([email][/email])> wrote:
I have searched the globe for Westerbeke 60 fuel lines with no luck. They are most certainly no longer available from the manufacturer. Does anyone have any ideas on sources for custom fuel line manufacturing resources?
Any thoughts are welcome.
Thanks!
-Bill Emberley
Running Tab #86Post generated from Pearson424 Forum using Mail2Forum
-
What kind of pressure are we talking here?
— Linus Sumocean <> wrote:
Quote:I was once told that I needed a matched set of fuel
lines by three different boat mechanics. They were
available at that time from Norshipco in Norfolk,
VA. To the tune of $565 that of course included
shipping. I could not believe that the lines had to
be so precise. I got in my car and started driving
after four stops, three cities and about 200 miles I
walked into Southeastern Diesel on the side of the
highway. Outside there were logging machines and
old oily trucks. When I walked through the door I
saw fuel lines hanging from the white walls. There
were several engines from a 65 Hatteras and glass
cases full of injector pumps. The man in the white
lab coat said ” that fuel line looks like it came of
a Perkins”. I had cracked the retainer nut on the
end of the line and it leaked. I told the man in
the lab coat that the boat mechanics told me the
lines had to be the exact same and I needed a new
one. He called to an older man in back that came
out in his white lab coat and took my line in back.
In less than a minute he returned with a new
compression fitting on the line and told me that he
had trimmed about 1/4″ off. I told the old man what
the others had told me and he said that if it didn’t
work that he would give my $2.50 back for the
repair.
The moral to this story is look for a heavy
equipment or other than marine source and the price
will be significantly cheaper. By the way that $2.50
repair worked just fine for about ten years.Linus
<.. snip>
Post generated from Pearson424 Forum using Mail2Forum
-
You're talking about 1500-3000 lbs pressure. Surprising, huh? Linus, what happened after 10 years?
On Tue, Jun 17, 2008 at 4:08 AM, alan P < ([email][/email])> wrote:
Quote:What kind of pressure are we talking here?— Linus Sumocean < ([email][/email])> wrote:
Quote:I was once told that I needed a matched set of fuel
lines by three different boat mechanics. They were
available at that time from Norshipco in Norfolk,
VA. To the tune of $565 that of course included
shipping. I could not believe that the lines had to
be so precise. I got in my car and started driving
after four stops, three cities and about 200 miles I
walked into Southeastern Diesel on the side of the
highway. Outside there were logging machines and
old oily trucks. When I walked through the door I
saw fuel lines hanging from the white walls. There
were several engines from a 65 Hatteras and glass
cases full of injector pumps. The man in the white
lab coat said ” that fuel line looks like it came of
a Perkins”. I had cracked the retainer nut on the
end of the line and it leaked. I told the man in
the lab coat that the boat mechanics told me the
lines had to be the exact same and I needed a new
one. He called to an older man in back that came
out in his white lab coat and took my line in back.
In less than a minute he returned with a new
compression fitting on the line and told me that he
had trimmed about 1/4″ off. I told the old man what
the others had told me and he said that if it didn't
work that he would give my $2.50 back for the
repair.
The moral to this story is look for a heavy
equipment or other than marine source and the price
will be significantly cheaper. By the way that $2.50
repair worked just fine for about ten years.Linus
<.. snip>
Post generated from Pearson424 Forum using Mail2Forum
-
Do people think that the lines need to be exact to
maintain some kind of timing with respect to the pump
and injectors?
ap
— Robert Fine <> wrote:You’re talking about 1500-3000 lbs pressure.
Surprising, huh? Linus, what
happened after 10 years?On Tue, Jun 17, 2008 at 4:08 AM, alan P
<> wrote:What kind of pressure are we talking here?
— Linus Sumocean <>
wrote:
I was once told that I needed a matched set of
fuel
lines by three different boat mechanics. They
were
available at that time from Norshipco in
Norfolk,
VA. To the tune of $565 that of course included
shipping. I could not believe that the lineshad to
be so precise. I got in my car and started
driving
after four stops, three cities and about 200
miles I
walked into Southeastern Diesel on the side of
the
highway. Outside there were logging machines
and
old oily trucks. When I walked through the door
I
saw fuel lines hanging from the white walls.
There
were several engines from a 65 Hatteras and
glass
cases full of injector pumps. The man in the
white
lab coat said ” that fuel line looks like it
came of
a Perkins”. I had cracked the retainer nut on
the
end of the line and it leaked. I told the man
in
the lab coat that the boat mechanics told me the
lines had to be the exact same and I needed anew
one. He called to an older man in back that
came
out in his white lab coat and took my line in
back.
In less than a minute he returned with a new
compression fitting on the line and told me thathe
had trimmed about 1/4″ off. I told the old man
what
the others had told me and he said that if it
didn’t
work that he would give my $2.50 back for the
repair.
The moral to this story is look for a heavy
equipment or other than marine source and theprice
will be significantly cheaper. By the way that
$2.50
Quote:Quote:repair worked just fine for about ten years.Linus
<.. snip>
Post generated from Pearson424 Forum using Mail2Forum
-
Not really. Once the lines are full, there shouldn't be a problem unless they are WAY different in length.
Bob
On Tue, Jun 17, 2008 at 4:21 AM, alan P < ([email][/email])> wrote:
Do people think that the lines need to be exact to
maintain some kind of timing with respect to the pump
and injectors?
ap— Robert Fine < ([email][/email])> wrote:
You're talking about 1500-3000 lbs pressure.
Surprising, huh? Linus, what
happened after 10 years?On Tue, Jun 17, 2008 at 4:08 AM, alan P
< ([email][/email])> wrote:What kind of pressure are we talking here?
— Linus Sumocean < ([email][/email])>
wrote:
I was once told that I needed a matched set of
fuel
lines by three different boat mechanics. They
were
available at that time from Norshipco in
Norfolk,
VA. To the tune of $565 that of course included
shipping. I could not believe that the lineshad to
be so precise. I got in my car and started
driving
after four stops, three cities and about 200
miles I
walked into Southeastern Diesel on the side of
the
highway. Outside there were logging machines
and
old oily trucks. When I walked through the door
I
saw fuel lines hanging from the white walls.
There
were several engines from a 65 Hatteras and
glass
cases full of injector pumps. The man in the
white
lab coat said ” that fuel line looks like it
came of
a Perkins”. I had cracked the retainer nut on
the
end of the line and it leaked. I told the man
in
the lab coat that the boat mechanics told me the
lines had to be the exact same and I needed anew
one. He called to an older man in back that
came
out in his white lab coat and took my line in
back.
In less than a minute he returned with a new
compression fitting on the line and told me thathe
had trimmed about 1/4″ off. I told the old man
what
the others had told me and he said that if it
didn't
work that he would give my $2.50 back for the
repair.
The moral to this story is look for a heavy
equipment or other than marine source and theprice
will be significantly cheaper. By the way that
$2.50
Quote:Quote:repair worked just fine for about ten years.Linus
<.. snip>
Post generated from Pearson424 Forum using Mail2Forum
-
Thats why I can’t see buying these custom lines for 5
and 600 dollars.
There’s a big over the road truck shop not to far from
here. I might wander down there and ask a few
questions. Better yet, a john deer tractor shop….
they do all kinds of tractors there…. framers are
cheap- like us…..ap
— Robert Fine <> wrote:
Not really. Once the lines are full, there
shouldn’t be a problem unless
they are WAY different in length.Bob
On Tue, Jun 17, 2008 at 4:21 AM, alan P
<> wrote:Do people think that the lines need to be exact to
maintain some kind of timing with respect to thepump
and injectors?
ap
— Robert Fine <> wrote:You’re talking about 1500-3000 lbs pressure.
Surprising, huh? Linus, what
happened after 10 years?On Tue, Jun 17, 2008 at 4:08 AM, alan P
<> wrote:What kind of pressure are we talking here?
— Linus Sumocean <>
wrote:
I was once told that I needed a matched set
of
fuel
lines by three different boat mechanics.
They
were
available at that time from Norshipco in
Norfolk,
VA. To the tune of $565 that of course
included
shipping. I could not believe that the
lines
had to
be so precise. I got in my car and started
driving
after four stops, three cities and about 200
miles I
walked into Southeastern Diesel on the side
of
the
highway. Outside there were logging
machines
and
old oily trucks. When I walked through the
door
I
saw fuel lines hanging from the white walls.
There
were several engines from a 65 Hatteras and
glass
cases full of injector pumps. The man in
the
white
lab coat said ” that fuel line looks like it
came of
a Perkins”. I had cracked the retainer nut
on
the
end of the line and it leaked. I told the
man
in
the lab coat that the boat mechanics told me
the
lines had to be the exact same and I needed
a
new
one. He called to an older man in back that
came
out in his white lab coat and took my line
in
back.
In less than a minute he returned with a new
compression fitting on the line and told methat
he
had trimmed about 1/4″ off. I told the old
man
what
the others had told me and he said that if
it
didn’t
work that he would give my $2.50 back for
the
repair.
The moral to this story is look for a heavy
equipment or other than marine source andthe
price
will be significantly cheaper. By the way
that
Quote:Quote:$2.50Quote:Quote:repair worked just fine for about ten years.Linus
<.. snip>
Post generated from Pearson424 Forum using Mail2Forum
-
I'd say that's the best bet. Go to a place that actually repairs engines and you'll be good to go. Not only will the mechanics be used to dealing with 10,000 hour engines, they'll understand how to make them work without 'OEM' parts.
Let us know how it goes – I'd really expect a very good repair for a very fair price.
Bob
On Tue, Jun 17, 2008 at 4:27 AM, alan P < ([email][/email])> wrote:
Thats why I can't see buying these custom lines for 5
and 600 dollars.
There's a big over the road truck shop not to far from
here. I might wander down there and ask a few
questions. Better yet, a john deer tractor shop….
they do all kinds of tractors there…. framers are
cheap- like us…..ap
— Robert Fine < ([email][/email])> wrote:
Not really. Once the lines are full, there
shouldn't be a problem unless
they are WAY different in length.Bob
On Tue, Jun 17, 2008 at 4:21 AM, alan P
< ([email][/email])> wrote:Do people think that the lines need to be exact to
maintain some kind of timing with respect to thepump
and injectors?
ap
— Robert Fine < ([email][/email])> wrote:You're talking about 1500-3000 lbs pressure.
Surprising, huh? Linus, what
happened after 10 years?On Tue, Jun 17, 2008 at 4:08 AM, alan P
< ([email][/email])> wrote:What kind of pressure are we talking here?
— Linus Sumocean < ([email][/email])>
wrote:
I was once told that I needed a matched set
of
fuel
lines by three different boat mechanics.
They
were
available at that time from Norshipco in
Norfolk,
VA. To the tune of $565 that of course
included
shipping. I could not believe that the
lines
had to
be so precise. I got in my car and started
driving
after four stops, three cities and about 200
miles I
walked into Southeastern Diesel on the side
of
the
highway. Outside there were logging
machines
and
old oily trucks. When I walked through the
door
I
saw fuel lines hanging from the white walls.
There
were several engines from a 65 Hatteras and
glass
cases full of injector pumps. The man in
the
white
lab coat said ” that fuel line looks like it
came of
a Perkins”. I had cracked the retainer nut
on
the
end of the line and it leaked. I told the
man
in
the lab coat that the boat mechanics told me
the
lines had to be the exact same and I needed
a
new
one. He called to an older man in back that
came
out in his white lab coat and took my line
in
back.
In less than a minute he returned with a new
compression fitting on the line and told methat
he
had trimmed about 1/4″ off. I told the old
man
what
the others had told me and he said that if
it
didn't
work that he would give my $2.50 back for
the
repair.
The moral to this story is look for a heavy
equipment or other than marine source andthe
price
will be significantly cheaper. By the way
that
Quote:Quote:$2.50Quote:Quote:repair worked just fine for about ten years.Linus
<.. snip>
Post generated from Pearson424 Forum using Mail2Forum
-
Showing my lack of experience with these engines, why do the fuel injector
lines need replacing. Is it due to corrosion of the line or because they
will no longer seal because of repeated opening and tightening to bleed the
lines. If it is the latter, that makes the case for an external fuel pump
pretty strong.Paul
To unsubscribe, e-mail:
For additional commands, e-mail:Post generated from Pearson424 Forum using Mail2Forum
-
They do corrode if not cared for – in some engines (maybe even ours) they're aluminum or an aluminum alloy that just due to the fact they're in a damp area and in contact with a bazillion other metals corrode.
Secondly, repeated bleeding with excessive force will maul the tubing surface resulting in a leak that requires more torque to seal, creating more leakage… until in an effort to stop the leak the nut cracks.
The torque specs for those tubes are in the inch-lb range, not foot-lb. The sealing surface is very narrow. The reason those tubes are as soft as they are is so that they (ostensibly the least expensive part) are the ones to fail, not the expensive fittings on the injectors or fuel pump.
Finally, between the lift pump and manual pump it should be an extraordinary circumstance to need to bleed the injector lines. Once the main injector pump is primed it will fill the lines. Sometimes it requires using the compression release (if we have one – I haven't looked) so you can spin the engine fast enough.
If the lift pump on the side of the engine isn't working, the engine may still run ok, but you won't be able to prime it properly. I know that when I change my filters, I let that pump run for a bit until it stops (you should hear clicking which eventually stops or slows considerably). Then I roll over the engine for a bit and it usually starts. It'll run rough for a few seconds and then all will be well. Perhaps, in this, I'm amazingly lucky.
Bob
On Tue, Jun 17, 2008 at 5:09 AM, Paul Lefebvre < ([email][/email])> wrote:
Showing my lack of experience with these engines, why do the fuel injector lines need replacing. Is it due to corrosion of the line or because they will no longer seal because of repeated opening and tightening to bleed the lines. If it is the latter, that makes the case for an external fuel pump pretty strong.
Paul
To unsubscribe, e-mail: ()
For additional commands, e-mail: ()—
Bob Fine
Fine Software LLC
Your data on the web your way. No kiddingPost generated from Pearson424 Forum using Mail2Forum
-
I am not sure all of us have an electric pump. I know
I don’t (w58). I have one purchased but not installed
(Walbro).
ap
— Robert Fine <> wrote:They do corrode if not cared for – in some engines
(maybe even ours) they’re
aluminum or an aluminum alloy that just due to the
fact they’re in a damp
area and in contact with a bazillion other metals
corrode.Secondly, repeated bleeding with excessive force
will maul the tubing
surface resulting in a leak that requires more
torque to seal, creating more
leakage… until in an effort to stop the leak the
nut cracks.The torque specs for those tubes are in the inch-lb
range, not foot-lb. The
sealing surface is very narrow. The reason those
tubes are as soft as they
are is so that they (ostensibly the least expensive
part) are the ones to
fail, not the expensive fittings on the injectors or
fuel pump.Finally, between the lift pump and manual pump it
should be an extraordinary
circumstance to need to bleed the injector lines.
Once the main injector
pump is primed it will fill the lines. Sometimes it
requires using the
compression release (if we have one – I haven’t
looked) so you can spin the
engine fast enough.If the lift pump on the side of the engine isn’t
working, the engine may
still run ok, but you won’t be able to prime it
properly. I know that when
I change my filters, I let that pump run for a bit
until it stops (you
should hear clicking which eventually stops or slows
considerably). Then I
roll over the engine for a bit and it usually
starts. It’ll run rough for a
few seconds and then all will be well. Perhaps, in
this, I’m amazingly
lucky.Bob
On Tue, Jun 17, 2008 at 5:09 AM, Paul Lefebvre
<>
wrote:Showing my lack of experience with these engines,
why do the fuel injector
lines need replacing. Is it due to corrosion of
the line or because they
will no longer seal because of repeated opening
and tightening to bleed the
lines. If it is the latter, that makes the case
for an external fuel pump
pretty strong.
Paul
To unsubscribe, e-mail:
For additional commands, e-mail:
—
Bob Fine
Fine Software LLC
Your data on the web your way. No kidding
To unsubscribe, e-mail:
For additional commands, e-mail:Post generated from Pearson424 Forum using Mail2Forum
-
You should have one on your W58. On the starboard side of the engine there should be a vertically mounted round thing about the size of a tomato paste can midway fore and aft. The fuel hose from the Racor, if you have one should run to it. Or maybe from the primary filter – I'll have to look. It will have two wires to it and little known to me, at least, there's a filter in it.
On Tue, Jun 17, 2008 at 5:32 AM, alan P < ([email][/email])> wrote:
I am not sure all of us have an electric pump. I know
I don't (w58). I have one purchased but not installed
(Walbro).
ap
— Robert Fine < ([email][/email])> wrote:They do corrode if not cared for – in some engines
(maybe even ours) they're
aluminum or an aluminum alloy that just due to the
fact they're in a damp
area and in contact with a bazillion other metals
corrode.Secondly, repeated bleeding with excessive force
will maul the tubing
surface resulting in a leak that requires more
torque to seal, creating more
leakage… until in an effort to stop the leak the
nut cracks.The torque specs for those tubes are in the inch-lb
range, not foot-lb. The
sealing surface is very narrow. The reason those
tubes are as soft as they
are is so that they (ostensibly the least expensive
part) are the ones to
fail, not the expensive fittings on the injectors or
fuel pump.Finally, between the lift pump and manual pump it
should be an extraordinary
circumstance to need to bleed the injector lines.
Once the main injector
pump is primed it will fill the lines. Sometimes it
requires using the
compression release (if we have one – I haven't
looked) so you can spin the
engine fast enough.If the lift pump on the side of the engine isn't
working, the engine may
still run ok, but you won't be able to prime it
properly. I know that when
I change my filters, I let that pump run for a bit
until it stops (you
should hear clicking which eventually stops or slows
considerably). Then I
roll over the engine for a bit and it usually
starts. It'll run rough for a
few seconds and then all will be well. Perhaps, in
this, I'm amazingly
lucky.Bob
On Tue, Jun 17, 2008 at 5:09 AM, Paul Lefebvre
< ([email][/email])>
wrote:Showing my lack of experience with these engines,
why do the fuel injector
lines need replacing. Is it due to corrosion of
the line or because they
will no longer seal because of repeated opening
and tightening to bleed the
lines. If it is the latter, that makes the case
for an external fuel pump
pretty strong.
Paul
To unsubscribe, e-mail:
For additional commands, e-mail:
—
Bob Fine
Fine Software LLC
Your data on the web your way. No kidding
To unsubscribe, e-mail: ()
For additional commands, e-mail: ()—
Bob Fine
Fine Software LLC
Your data on the web your way. No kiddingPost generated from Pearson424 Forum using Mail2Forum
-
I'll take a picture tonight and send it along.
On Tue, Jun 17, 2008 at 5:32 AM, alan P < ([email][/email])> wrote:
I am not sure all of us have an electric pump. I know
I don't (w58). I have one purchased but not installed
(Walbro).
ap
— Robert Fine < ([email][/email])> wrote:They do corrode if not cared for – in some engines
(maybe even ours) they're
aluminum or an aluminum alloy that just due to the
fact they're in a damp
area and in contact with a bazillion other metals
corrode.Secondly, repeated bleeding with excessive force
will maul the tubing
surface resulting in a leak that requires more
torque to seal, creating more
leakage… until in an effort to stop the leak the
nut cracks.The torque specs for those tubes are in the inch-lb
range, not foot-lb. The
sealing surface is very narrow. The reason those
tubes are as soft as they
are is so that they (ostensibly the least expensive
part) are the ones to
fail, not the expensive fittings on the injectors or
fuel pump.Finally, between the lift pump and manual pump it
should be an extraordinary
circumstance to need to bleed the injector lines.
Once the main injector
pump is primed it will fill the lines. Sometimes it
requires using the
compression release (if we have one – I haven't
looked) so you can spin the
engine fast enough.If the lift pump on the side of the engine isn't
working, the engine may
still run ok, but you won't be able to prime it
properly. I know that when
I change my filters, I let that pump run for a bit
until it stops (you
should hear clicking which eventually stops or slows
considerably). Then I
roll over the engine for a bit and it usually
starts. It'll run rough for a
few seconds and then all will be well. Perhaps, in
this, I'm amazingly
lucky.Bob
On Tue, Jun 17, 2008 at 5:09 AM, Paul Lefebvre
< ([email][/email])>
wrote:Showing my lack of experience with these engines,
why do the fuel injector
lines need replacing. Is it due to corrosion of
the line or because they
will no longer seal because of repeated opening
and tightening to bleed the
lines. If it is the latter, that makes the case
for an external fuel pump
pretty strong.
Paul
To unsubscribe, e-mail:
For additional commands, e-mail:
—
Bob Fine
Fine Software LLC
Your data on the web your way. No kidding
To unsubscribe, e-mail: ()
For additional commands, e-mail: ()—
Bob Fine
Fine Software LLC
Your data on the web your way. No kiddingPost generated from Pearson424 Forum using Mail2Forum
-
I rewired my engine last winter. No electric fuel
pump.
ap— Robert Fine <> wrote:
I’ll take a picture tonight and send it along.
On Tue, Jun 17, 2008 at 5:32 AM, alan P
<> wrote:I am not sure all of us have an electric pump. I
know
I don’t (w58). I have one purchased but not
installed
(Walbro).
ap
— Robert Fine <> wrote:They do corrode if not cared for – in some
engines
(maybe even ours) they’re
aluminum or an aluminum alloy that just due tothe
fact they’re in a damp
area and in contact with a bazillion othermetals
corrode.
Secondly, repeated bleeding with excessive force
will maul the tubing
surface resulting in a leak that requires more
torque to seal, creating more
leakage… until in an effort to stop the leakthe
nut cracks.
The torque specs for those tubes are in the
inch-lb
range, not foot-lb. The
sealing surface is very narrow. The reasonthose
tubes are as soft as they
are is so that they (ostensibly the leastexpensive
part) are the ones to
fail, not the expensive fittings on theinjectors or
fuel pump.
Finally, between the lift pump and manual pump
it
should be an extraordinary
circumstance to need to bleed the injectorlines.
Once the main injector
pump is primed it will fill the lines.Sometimes it
requires using the
compression release (if we have one – I haven’t
looked) so you can spin the
engine fast enough.If the lift pump on the side of the engine isn’t
working, the engine may
still run ok, but you won’t be able to prime it
properly. I know that when
I change my filters, I let that pump run for abit
until it stops (you
should hear clicking which eventually stops orslows
considerably). Then I
roll over the engine for a bit and it usually
starts. It’ll run rough for a
few seconds and then all will be well. Perhaps,in
this, I’m amazingly
lucky.Bob
On Tue, Jun 17, 2008 at 5:09 AM, Paul Lefebvre
<>
wrote:Showing my lack of experience with these
engines,
why do the fuel injector
lines need replacing. Is it due to corrosion
of
the line or because they
will no longer seal because of repeated
opening
and tightening to bleed the
lines. If it is the latter, that makes the
case
for an external fuel pump
pretty strong.
Paul
To unsubscribe, e-mail:
For additional commands, e-mail:
—
Bob Fine
Fine Software LLC
Your data on the web your way. No kidding
To unsubscribe, e-mail:
For additional commands, e-mail:
—
Bob Fine
Fine Software LLC
Your data on the web your way. No kidding
To unsubscribe, e-mail:
For additional commands, e-mail:Post generated from Pearson424 Forum using Mail2Forum
-
What year is your W58?
Bob
On Tue, Jun 17, 2008 at 5:53 AM, alan P < ([email][/email])> wrote:
I rewired my engine last winter. No electric fuel
pump.ap
— Robert Fine < ([email][/email])> wrote:
I'll take a picture tonight and send it along.
On Tue, Jun 17, 2008 at 5:32 AM, alan P
< ([email][/email])> wrote:I am not sure all of us have an electric pump. I
know
I don't (w58). I have one purchased but not
installed
(Walbro).
ap
— Robert Fine < ([email][/email])> wrote:They do corrode if not cared for – in some
engines
(maybe even ours) they're
aluminum or an aluminum alloy that just due tothe
fact they're in a damp
area and in contact with a bazillion othermetals
corrode.
Secondly, repeated bleeding with excessive force
will maul the tubing
surface resulting in a leak that requires more
torque to seal, creating more
leakage… until in an effort to stop the leakthe
nut cracks.
The torque specs for those tubes are in the
inch-lb
range, not foot-lb. The
sealing surface is very narrow. The reasonthose
tubes are as soft as they
are is so that they (ostensibly the leastexpensive
part) are the ones to
fail, not the expensive fittings on theinjectors or
fuel pump.
Finally, between the lift pump and manual pump
it
should be an extraordinary
circumstance to need to bleed the injectorlines.
Once the main injector
pump is primed it will fill the lines.Sometimes it
requires using the
compression release (if we have one – I haven't
looked) so you can spin the
engine fast enough.If the lift pump on the side of the engine isn't
working, the engine may
still run ok, but you won't be able to prime it
properly. I know that when
I change my filters, I let that pump run for abit
until it stops (you
should hear clicking which eventually stops orslows
considerably). Then I
roll over the engine for a bit and it usually
starts. It'll run rough for a
few seconds and then all will be well. Perhaps,in
this, I'm amazingly
lucky.Bob
On Tue, Jun 17, 2008 at 5:09 AM, Paul Lefebvre
< ([email][/email])>
wrote:Showing my lack of experience with these
engines,
why do the fuel injector
lines need replacing. Is it due to corrosion
of
the line or because they
will no longer seal because of repeated
opening
and tightening to bleed the
lines. If it is the latter, that makes the
case
for an external fuel pump
pretty strong.
Paul
To unsubscribe, e-mail:
For additional commands, e-mail:
—
Bob Fine
Fine Software LLC
Your data on the web your way. No kidding
To unsubscribe, e-mail:
For additional commands, e-mail:
—
Bob Fine
Fine Software LLC
Your data on the web your way. No kidding
To unsubscribe, e-mail: ()
For additional commands, e-mail: ()—
Bob Fine
Fine Software LLC
Your data on the web your way. No kiddingPost generated from Pearson424 Forum using Mail2Forum
-
1981
— Robert Fine <> wrote:What year is your W58?
Bob
On Tue, Jun 17, 2008 at 5:53 AM, alan P
<> wrote:I rewired my engine last winter. No electric fuel
pump.
ap— Robert Fine <> wrote:
I’ll take a picture tonight and send it along.
On Tue, Jun 17, 2008 at 5:32 AM, alan P
<> wrote:I am not sure all of us have an electric pump.
I
know
I don’t (w58). I have one purchased but not
installed
(Walbro).
ap
— Robert Fine <> wrote:They do corrode if not cared for – in some
engines
(maybe even ours) they’re
aluminum or an aluminum alloy that just dueto
the
fact they’re in a damp
area and in contact with a bazillion othermetals
corrode.
Secondly, repeated bleeding with excessive
force
will maul the tubing
surface resulting in a leak that requiresmore
torque to seal, creating more
leakage… until in an effort to stop theleak
the
nut cracks.
The torque specs for those tubes are in the
inch-lb
range, not foot-lb. The
sealing surface is very narrow. The reasonthose
tubes are as soft as they
are is so that they (ostensibly the leastexpensive
part) are the ones to
fail, not the expensive fittings on theinjectors or
fuel pump.
Finally, between the lift pump and manual
pump
it
should be an extraordinary
circumstance to need to bleed the injectorlines.
Once the main injector
pump is primed it will fill the lines.Sometimes it
requires using the
compression release (if we have one – Ihaven’t
looked) so you can spin the
engine fast enough.If the lift pump on the side of the engine
isn’t
working, the engine may
still run ok, but you won’t be able to primeit
properly. I know that when
I change my filters, I let that pump run fora
bit
until it stops (you
should hear clicking which eventually stopsor
slows
considerably). Then I
roll over the engine for a bit and itusually
starts. It’ll run rough for a
few seconds and then all will be well.Perhaps,
in
this, I’m amazingly
lucky.Bob
On Tue, Jun 17, 2008 at 5:09 AM, Paul
Lefebvre
<>
wrote:Showing my lack of experience with these
engines,
why do the fuel injector
lines need replacing. Is it due to
corrosion
of
the line or because they
will no longer seal because of repeated
opening
and tightening to bleed the
lines. If it is the latter, that makes the
case
for an external fuel pump
pretty strong.
Paul
To unsubscribe, e-mail:
For additional commands, e-mail:
—
Bob Fine
Fine Software LLC
Your data on the web your way. No kidding
To unsubscribe, e-mail:
For additional commands, e-mail:
—
Bob Fine
Fine Software LLC
Your data on the web your way. No kidding
To unsubscribe, e-mail:
For additional commands, e-mail:
—
Bob Fine
Fine Software LLC
Your data on the web your way. No kidding
To unsubscribe, e-mail:
For additional commands, e-mail:Post generated from Pearson424 Forum using Mail2Forum
-
I asked my local Westerbeke dealer if W60 injection lines were available several years ago. He said that they were no longer available. If they need a new injection line, they make them up. I assume that their pricing for injection lines is similar to to their pricing for starter motors. $2.50 sounds pretty good to me. I wonder what the Westerbeke dealer would charge, $700/set?
—
Rich Carter
Original message
<.. snip>Post generated from Pearson424 Forum using Mail2Forum
-
Hi Chuck,
Sorry for the late response. I will call you first thing tomorrow as I am on left  coast time.
BillSent from my iPhone
On Jun 16, 2008, at 6:29 PM, “Chuck Ruble” < ([email][/email])> wrote:
Bill, call me I have two used sets. 804-370-2271.
On 6/16/08, Bill Emberley <()> wrote:
I have searched the globe for Westerbeke 60 fuel lines with no luck. They are most certainly no longer available from the manufacturer. Does anyone have any ideas on sources for custom fuel line manufacturing resources?
Any thoughts are welcome.Â
Thanks!
-Bill Emberley
Running Tab #86Post generated from Pearson424 Forum using Mail2Forum
-
-
-
- You must be logged in to reply to this topic.