×

Lewmar 30 Self Tailing Overhaul

Home / Topic / Lewmar 30 Self Tailing Overhaul

Forums › General Discussion › Lewmar 30 Self Tailing Overhaul

Viewing 6 reply threads
  • Author
    Posts
    • June 26, 2008 at 4:23 pm #67069
      Anonymous

      I have an older Lewmar 30 that I have been trying to figure out how to dissymble for maint.
      Any source out there of how-to or diagrams? This unit does not have the “screw off cap” shown on the Lewmar site. It is self tailing single speed.
      Thanks – Eric

      Post generated from Pearson424 Forum using Mail2Forum

    • June 26, 2008 at 4:51 pm #70252
      RichCarter
      Participant

      A Link to the manual is below. Damn if I can see how the cap comes off though.

      http://en.lewmar.com/support/PDF/Vol10_WEB.zip

      Rich

      Quote:
      <.. snip>

      Post generated from Pearson424 Forum using Mail2Forum

    • June 26, 2008 at 5:58 pm #70254
      quent
      Participant

      Maybe it’s an older “wave grip” model. Try this link to Pyacht.com
      http://www.pyacht.com/online-store/scstore/graphics/Lew_WG_30st.gif

      Quent

    • June 26, 2008 at 9:46 pm #70255
      Anonymous

      Hi Eric,
      I have a very nice pamphlet B2304 Issue 6 – Winch Service Manual – Standard and Self Tailing Models 6 to 66. It contains instructions and photos. Unfortunetely it seems to cover only the more recent Ocean Series (like the manual Rich refered to). However, there is a page (page 49) which lists the manuals for earlier models. It indicates that Service Manual 6 Starting March 85 applies to model 30 ST.
      Good luck,
      Phil Fontaine
      Aurora

      Quote:
      Original Message

      <.. snip>

      Post generated from Pearson424 Forum using Mail2Forum

    • June 26, 2008 at 9:50 pm #70256
      unabated
      Participant

      These are the winches that are on the mast? I seem to
      remember that there is a left hand thread involved
      here. I just can’t remember which part. I had mine
      apart last year. Sucks to get old…..
      alan

      To unsubscribe, e-mail:
      For additional commands, e-mail:

      Post generated from Pearson424 Forum using Mail2Forum

    • June 26, 2008 at 10:35 pm #70258
      unabated
      Participant

      It’s coming back to me….
      Try rapping the self-tailer with a rubber mallet, I
      still think it’s a left hand thread, but try it both
      ways…..
      alan
      — quent <> wrote:

      Maybe it’s an older “wave grip” model. Try this
      link to Pyacht.com

      http://www.pyacht.com/online-store/scstore/graphics/Lew_WG_30st.gif

      Quent

      To unsubscribe, e-mail:
      For additional commands, e-mail:

      Post generated from Pearson424 Forum using Mail2Forum

    • June 27, 2008 at 6:31 am #70259
      Anonymous

      rich, the one shown in your manual has a screw off cap.
      Eric some older ones had a split ring around the top, if you take a picture i might be able to tell you. David Thompson

      On Thu, Jun 26, 2008 at 12:51 PM, Rich Carter wrote:

      A Link to the manual is below. Damn if I can see how the cap comes off though.

      http://en.lewmar.com/support/PDF/Vol10_WEB.zip

      Rich

      ___________________________________

      <.. snip>

      Post generated from Pearson424 Forum using Mail2Forum

  • Author
    Posts
Viewing 6 reply threads
  • You must be logged in to reply to this topic.