- This topic has 13 replies, 5 voices, and was last updated 12 years, 10 months ago by
.
-
Posts
-
-
Anyone have a spare section of Profurl 42mm classic extrusion? The top
section of mine has some bad erosion on the sail tracks and I have it
down to trim properly (it has always been too long) ahead of new sails
arriving. The NC42,NC42i, LC42, LC42i, LC42S, LC42Si, C42, and C42 all
use the same extrusion. (I need one of the sections that is not the one
with the gate).Thanks,
Pete
Melbourne, FL_______________________________________________
maillist mailing listhttps://pearson424.org/mailman/listinfo/maillist_pearson424.org
Post generated from Pearson424 Forum using Mail2Forum
-
-
-
That’s unhappy news about ProFurl. I’ve long thought
they were one of the good ones. What brand(s) are savvy
sailors buying these days?Tor
Silverheels, P-424 #17
http://www.silverheels.us
Quote:
Original Message
Post generated from Pearson424 Forum using Mail2Forum
-
seems there a plenty available for $175 to $250 per section… But I
have found some used ones. I just have a 90 minute round trip car drive
to go get it.On 12/4/2013 8:56 PM, wrote:
Quote:My rigger mentioned to me last summer that Profurl is no longer providing parts. If you can find a piece you are fortunate.Regards
Rich
Original Message
Post generated from Pearson424 Forum using Mail2Forum
-
I am getting a Facnor for my new code zero.
On 12/5/2013 7:43 AM, Silverheels wrote:
Quote:That’s unhappy news about ProFurl. I’ve long thought
they were one of the good ones. What brand(s) are savvy
sailors buying these days?Tor
Silverheels, P-424 #17
http://www.silverheels.us
Quote:
Original Message
Post generated from Pearson424 Forum using Mail2Forum
-
-
-
understood. I have a map of the different profiles.
On 12/5/2013 9:13 AM, quent wrote:
Make sure that the connections are the same. Can’t speak to profurl, but on harken different generations won’t always fit each other.
Quent_______________________________________________
maillist mailing listhttps://pearson424.org/mailman/listinfo/maillist_pearson424.org
_______________________________________________
maillist mailing listhttps://pearson424.org/mailman/listinfo/maillist_pearson424.org
Post generated from Pearson424 Forum using Mail2Forum
-
-
I did indeed. Crazy story… I drove 45 minutes to the boat yard where
I had launched my boat to pick up a section from a bloke (English fellow
in fact) who said he had one. It was not even close to what I had and
probably not even made by profurl. But while there I asked the yard
owner for any suggestions and that lead me to a loft which turned out
had a section in their pile of tubing, etc. So we put up the rig on
Saturday only to find that the 5/8″ clevis pins I ordered, though
labeled 5/8″ were actually 3/4″… so the adventure continues. So I
crewed on a racing boat yesterday instead of sailing our boat.All the best,
Pete
On 12/8/2013 8:32 PM, Chuck Ruble wrote:
Pete, did you find a replacement segment for the top extrusion yet?
Chuck
_______________________________________________
maillist mailing listhttps://pearson424.org/mailman/listinfo/maillist_pearson424.org
_______________________________________________
maillist mailing listhttps://pearson424.org/mailman/listinfo/maillist_pearson424.org
Post generated from Pearson424 Forum using Mail2Forum
-
-
-
-
- You must be logged in to reply to this topic.