- This topic has 6 replies, 3 voices, and was last updated 17 years, 5 months ago by
.
-
Posts
-
-
I am looking for a supplier for 3/8″ x 3/8″ gasket material for the very old ports on my 424.
Don’t know what manufacturer made them as there are no marks. They are aluminum, with the glass seald in by a sandwich construction, The channel for the gasket looks to have been machined in and is square. Any ideas? I took them apart this winter and glass bead blasted them and rebeaded the glass – came out pretty good.
Any ideas?Eric
Post generated from Pearson424 Forum using Mail2Forum
-
The hatches were made by Bomar, who recently stopped producing the gaskets for them. I purchased 3/8 x 3/8 rubber from McMaster Carr and used that.
Bob
On Mon, May 25, 2009 at 8:16 PM, Eric Lorentzon < ([email][/email])> wrote:
I am looking for a supplier for 3/8″ x 3/8″ gasket material for the very old ports on my 424.
Don't know what manufacturer made them as there are no marks. They are aluminum, with the glass seald in by a sandwich construction, The channel for the gasket looks to have been machined in and is square. Any ideas? I took them apart this winter and glass bead blasted them and rebeaded the glass – came out pretty good.
Any ideas?
Eric
—
Bob Fine
s/v Pelican
Hull #8Post generated from Pearson424 Forum using Mail2Forum
-
http://www.pleasureboatmarine.com/bomp2000255.html pricey
I think I got some from defender when I did mine
Pete
Eric Lorentzon wrote:
I am looking for a supplier for 3/8″ x 3/8″ gasket material for the
very old ports on my 424.
Don’t know what manufacturer made them as there are no marks. They are
aluminum, with the glass seald in by a sandwich construction, The
channel for the gasket looks to have been machined in and is square.
Any ideas? I took them apart this winter and glass bead blasted them
and rebeaded the glass – came out pretty good.
Any ideas?Eric
To unsubscribe, e-mail:
For additional commands, e-mail:Post generated from Pearson424 Forum using Mail2Forum
-
I tried to get it from Defender last year and they said they weren't going to carry it anymore – they had like 2' left.
Good luck!
Bob
On Tue, May 26, 2009 at 9:57 AM, Pete Dubler < ([email][/email])> wrote:
http://www.pleasureboatmarine.com/bomp2000255.html pricey
I think I got some from defender when I did mine
Pete
Eric Lorentzon wrote:
I am looking for a supplier for 3/8″ x 3/8″ gasket material for the very old ports on my 424.
Don't know what manufacturer made them as there are no marks. They are aluminum, with the glass seald in by a sandwich construction, The channel for the gasket looks to have been machined in and is square. Any ideas? I took them apart this winter and glass bead blasted them and rebeaded the glass – came out pretty good.
Any ideas?
Eric
To unsubscribe, e-mail: ()
For additional commands, e-mail: ()—
Bob Fine
s/v Pelican
Hull #8Post generated from Pearson424 Forum using Mail2Forum
-
I have since learned the material was likely “viton” a dupont product.
It is available as “cordage” in 3/8″x3/8″ from many rubber products distributors.
I have ordered 10ft from “rainbow rubber” – will see if it is the right stuff.
Thanks all for the resources and leads –Eric
— On Tue, 5/26/09, Robert Fine <> wrote:
Quote:<.. snip>Post generated from Pearson424 Forum using Mail2Forum
-
-
I will post my sucess (hopefuly).
Here is the contact information for my source:
Jack Herston
Rainbow Rubber Extrusions Inc.
()
phone 330.848.2255 fax 330.848.9990
http://www.rainbowrubber.com— On Wed, 5/27/09, <> wrote:
Quote:<.. snip>Post generated from Pearson424 Forum using Mail2Forum
-
- You must be logged in to reply to this topic.