Forum Replies Created

Viewing 15 posts - 1 through 15 (of 43 total)
  • Author
    Posts
  • in reply to: parts off w-60 westerbeke #225660
    Pjfuce
    Participant

    i have starter rebuilt 2019
    heat exchanger new 2019
    exhaust manifold cleaned and re furbished 2019

    all for sale
    plus block minus transmission motor mounts for sale,

    please call i will be listing on ebay and craigslist shortly but wanted to help out members first

    paul
    973.518.8791

    in reply to: parts off w-60 westerbeke #225632
    Pjfuce
    Participant

    update on W60

    engine is out of boat and i have removed transmission (which i will be using), removed head and right now it looks like it was a blown head gasket but will be doing a little more investigation. i might also keep the raw water pump for a spare as it is the same on newer engine.

    the parts i will look to sell are:

    whole engine minus trans and water pump
    or parting out the following:

    injector pump rebuilt 2018
    starter rebuilt 2019
    heat exchanger new 2019
    exhaust manifold refurbished cleaned 2019
    exhaust pot stainless steel
    oil and trans cooler
    water pump (closed fresh water)
    injectors rebuilt and calibrated 2017
    injector lines

    please call with any questions

    paul 973.518.8791

    in reply to: How many gallons of bottom paint? #225630
    Pjfuce
    Participant

    hi,

    i have used trinadad Sr the last 2 times i did my bottom always very clean . i leave boat in water all year long up north in summer and in florida for the winter. 3gals and that should give you enough.

    paul
    SV SpellBound #80
    Atlantic Highlands NJ

    in reply to: parts off w-60 westerbeke #225597
    Pjfuce
    Participant

    no sorry will be using same trans snd v drive and shaft

    paul

    in reply to: parts off w-60 westerbeke #225592
    Pjfuce
    Participant

    ok let me get engine of boat and then i will contact you, where are you located?

    paul

    in reply to: Water Tank #225579
    Pjfuce
    Participant

    not sure i will be down on boat in a couple weeks will check it out. my westerbeke 60 decided to become a 3 cylinder engine instead of 4! found a w60 with 950 hrs on it in Ft Lauderdale having it shipped north now and will put all upgrades on my engine on newer one and plug back in boat hopefully all done before end of june, then back up north for rest of summer.

    paul

    in reply to: Water Tank #225577
    Pjfuce
    Participant

    hi ben

    i have hull #80, i have plastic tanks which i always assumed we installed by a previous owner. apparently they were installed in build of boat!

    Paul
    Spell Bound #80

    in reply to: compression on a w-58 #225436
    Pjfuce
    Participant

    paul
    spell bound #80 1979 ketch

    w-60

    i had my compression checked 2years ago and had about 330-333 on all cylinders. i thought i saw in one of my books on engine that original was 427 psi but i will check agian when i get back south on it in a couple weeks

    in reply to: Cutter Ketch inner stay position #225389
    Pjfuce
    Participant

    i have a cutter rigged ketch, i have yet to fly the storm jib but i did rig it up see pics attached. i have running back stays on main and mizzen mast, i will take additional pics of how storm stay connects to deck which is behind anchor winch.

    paul

    Attachments:
    1. EAADF0AF-AE6F-424D-9EAA-3599B76E98A9.jpeg

    in reply to: 424 20” fixed prop #225338
    Pjfuce
    Participant

    is prop still available?

    Paul
    Spell Bound# 80

    in reply to: Chesapeake Bay meet-up #225337
    Pjfuce
    Participant

    I will be traveling north from Bahamas back to NJ late may early june and would love to meet up!

    Paul
    SV Spell Bound #80

    in reply to: V-Drive: original and in good condition – $250 OBO #224443
    Pjfuce
    Participant

    Hi

    Paul from sv spell bound#80, i am interested if you could send pics? Also what engine did you remove i have a w-60.

    Thank you

    in reply to: Parting out Westerbeke W58 #223925
    Pjfuce
    Participant

    Evan:

    I am interested in glow plus, injector lines, mixer elbow on raw water if avialable.

    Paul
    Spell Bound#80

    in reply to: parting W-58 #223429
    Pjfuce
    Participant
    Randy
    You had mentioned you might be passing this way heading south for winter (NJ) might be able to meet as I am in no rush for parts?  As far as an offer I don't know around $300 or so? Let me know what you think
    Paul

    in reply to: parting W-58 #223385
    Pjfuce
    Participant
    I would be interested in glow plugs, just had injector pump rebuilt and alternator, maybe also injector lines, and exhaust manifold.
    Paul
    SV Cygnus #80

Viewing 15 posts - 1 through 15 (of 43 total)